9/3/2023 0 Comments Diy led light panelIt's so much easier and I care about you and don't want you to get hurt, honey. You can replace them with something that is safer to work with, namely high-CRI LED strips that have adhesive on the back.You can use its own light source-those LED strips or CCFL bulbs-which will require you to be very knowledgeable about electronics so as not to electrocute yourself or burn down your house. The next big hurdle to jump over after disassembling your display is powering the thing, and now that all of its power components are in discarded piles of plastic and electronics and metal, it obviously won't be as easy as plugging it in. They're made of glass and contain mercury. The light used to illuminate the screen is typically going to be a strip or strips of LEDs, but some screens use CCFL bulbs or lamps. The backlight panel is made up of several layers, including a fresnel lens layer, diffusion layer, and various reflectors. Remove the metal border and LCD panel until you're left with just the backlight panel. (I'm hating myself big time right now because I just threw away not one, not two, but three friggin' monitors just a few months ago.)Īs Perks demonstrates, it's mostly just a matter of disassembling your display-unscrewing the back panel and removing (carefully) all the internal electronics and metal components. According to Perks, this layer makes the light appear to be coming from further away and thus softening your shadows-an ideal effect if you're going for daylight.Īgain, you can do this trick with pretty much any display, be it a TV screen or computer monitor. Why are TVs and monitors make such good (and crazy accurate) daylight light panels? A lot of it has to do with the fresnel lens layer, diffusion pads, and various reflectors used inside a lot of these units to direct the light forward. Seriously, you'll probably never throw out another screen again. In this tutorial, Matthew Perks of DIY Perks shows you a super clever way to repurpose your busted ass TV or computer monitor and turn it into a surprisingly effective DIY daylight light panel. Now the screen's shattered and you have to throw it out, right? Wrongo. Drill a 3/8″ hole into the bottom center of the light panel frame and insert the 1/4″-20 threaded insert into the 've done gone and did it, didn't ya? You had a raging Bronie gathering.or whatever.someone got a little too hopped up on party juice and bellyflopped onto your sweet LCD TV.Install the prism light panel onto the frame using the 1/2″ pan head screws.Using the hot glue gun, secure the jumper wires to the panel.Test the light panel that all strips light up as you expect.Solder the jumper wires on the LED light strips.Strip and pre-tin all of the wires and solder points of the LED light strips.Cut the small 18ga wire into lengths to reach from strip to strip inside the panel.Feed the power cord through the hole in the frame (Step 5) and tie a knot in the wire to keep from pulling the wire out of the panel by accident later.Unpack the LED Light Kit and cut the strips to the desired length to fit inside the frame.Drill a 1/4″ hole through the side of the frame to fish the power cord through.This will hold the panel in place while the glue sets and allow you to keep working. Using the stapler and 1/2″ staples, secure the smooth panel to the wood frame. Using the clear glue, run a bead around the whole wood frame, then place the smooth white panel on top of it.Be sure to put a bit of wood glue on each of the joints, too. Assemble the frame by drilling pilot holes and countersinking for the 1.5″ wood screws to attach the pine pieces together.Rip the pine board into 1″ wide strips, then cut it to the required lengths to make a frame the same size as the panels you cut in Step 1.Cut the prism and smooth panels to the size you want your LED light panel to be.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |